Bearing suffixes: what do 2RS, ZZ, C3, K and E mean?
Updated: 19 November 2026 · Çağ Rulman technical team
Short answer
Suffixes follow the basic number and describe features, not size: 2RS means rubber seals on both sides, ZZ (2Z) metal shields on both sides, C3 internal clearance greater than normal, K tapered bore (1:12), E reinforced internal design and M brass cage. For example 6204, 6204-2RS and 6204-ZZ all measure 20 × 47 × 14 mm.
Seal and shield suffixes
The same feature is written differently by each brand; the equivalents listed are interchangeable.
| Suffix | Meaning | When to choose it |
|---|---|---|
| 2RS · 2RS1 · 2RSH · 2RSR · DDU · LLU | Rubber seals on both sides | Best protection against dust, water and dirt; greased for life. |
| RS · RS1 · RSH · RSR · DU · LU | Rubber seal on one side | One side open; when the other side is protected by the housing. |
| ZZ · 2Z · 2ZR | Metal shields on both sides | Keeps out coarse dust with low friction; suits high speeds. |
| Z · ZR | Metal shield on one side | One side open, one side shielded. |
| No suffix | Open type | Gearboxes and housings with oil bath or external lubrication. |
2RS vs ZZ vs open: comparison
| Property | 2RS (rubber sealed) | ZZ (metal shielded) | Open |
|---|---|---|---|
| Protection against dust and water | Very good | Moderate (coarse dust) | None (housing protects) |
| Friction | Highest | Low | Lowest |
| Permissible speed | Lowest | High | Highest |
| Lubrication | Greased for life | Greased for life | External oil or grease |
| Typical use | Agriculture, construction, damp areas, conveyors | Electric motors, fans, pumps | Gearboxes and oil-bath housings |
Clearance suffixes: C2, C3, C4
Internal clearance is the small play between rolling elements and rings. It shrinks as the bearing heats up or is mounted with an interference fit, so C3 is chosen for warm-running applications.
| Suffix | Clearance | Use |
|---|---|---|
| C2 | Smaller than normal | Vibration-free, precise and cool-running applications |
| CN | Normal (not marked) | General use |
| C3 | Greater than normal | Warm-running bearings with tight fits; electric motors |
| C4 | Greater than C3 | High temperature and vibration: screens, vibrators, dryers |
| C5 | Greater than C4 | Very high temperature; special applications |
Bore, design and other suffixes
| Suffix | Meaning | Notes |
|---|---|---|
| K | Tapered bore (1:12) | Mounted on the shaft with a sleeve (spherical roller and self-aligning ball bearings). |
| K30 | Tapered bore (1:30) | Wide spherical roller bearings of series 240 and 241. |
| E | Reinforced internal design | Higher load rating in the same size. |
| CA · CC · MB | Spherical roller bearing design | Cage and internal design variants; CA and MB have brass cages, CC steel cages. |
| W33 | Lubrication groove | Lubrication groove and three holes in the outer ring. |
| NR | Snap ring groove with snap ring | The snap ring on the outer ring locates the bearing axially in the housing. |
| P6 · P5 · P4 | Precision class | Tighter tolerances than normal (P0); machine tool spindles. |
Cage suffixes
| Suffix | Cage | Suitable for |
|---|---|---|
| M · MA · MB | Machined brass cage | Heavy loads, vibration, high temperature |
| J · JP · Y | Pressed steel cage | General use |
| TN9 · TVP · TVH · T | Glass-fibre reinforced polyamide cage | Light and quiet; up to about 120 °C |
The way suffixes are written can differ slightly by brand and production series. For cross-brand equivalents see the interchange chart.
Frequently asked questions
Should I choose 2RS or ZZ?
Choose 2RS where there is dust, water or moisture and ZZ for high speeds in clean conditions. The sizes are the same, so they are interchangeable.
When do I need C3?
When the bearing runs warm or is fitted tightly on the shaft; it is common in electric motors.
What is the difference between SKF 2RSH and 2RS1?
Both are SKF designs with contact rubber seals on both sides; 2RSH is the newer seal design. The dimensions are the same.
