How to choose the right shaft seal size
Updated: 19 November 2026 · Çağ Rulman technical team
Short answer
A radial shaft seal’s inner diameter equals the shaft diameter and its outer diameter the housing bore; the width depends on the space available. A seal fitted next to a bearing usually has the same inner and outer diameter as the bearing: for 6204 (20 × 47 × 14 mm) use a 20 × 47 × 7 mm seal. Choose NBR for general use and FKM (Viton) above 100 °C.
Step by step
- Inner diameter: the shaft diameter (bearing bore d).
- Outer diameter: the housing bore (usually the bearing outside diameter D).
- Width: to suit the space available; standard widths are e.g. 7, 8, 10, 12 mm.
- Lip type: double lip (TC) in dusty conditions.
- Material: NBR or FKM depending on temperature.
Material comparison: NBR vs FKM
| Material | Temperature range | Properties | Typical use |
|---|---|---|---|
| NBR (nitrile) | About −40 … +100 °C | Resists oil and grease, economical | Motors, pumps, gearboxes |
| FKM (Viton) | About −20 … +200 °C | Resists high temperatures and chemicals | Hot gearboxes, chemicals, near furnaces |
Lip types
| Type | Design | Use |
|---|---|---|
| TC | Double lip, spring loaded, rubber covered OD | Most common; the main lip holds the lubricant, the dust lip keeps dirt out |
| SC | Single lip, spring loaded, rubber covered OD | Clean environments |
| TB | Double lip, spring loaded, metal OD | Where a firm fit in a metal bore is needed |
| SB | Single lip, spring loaded, metal OD | Clean environment, metal bore |
Seal sizes for common bearings
| Bearing | Size (d × D × B) | Matching seal (d × D × b) |
|---|---|---|
| 6201 | 12 × 32 × 10 mm | 12 × 32 × 7 mm |
| 6202 | 15 × 35 × 11 mm | 15 × 35 × 7 mm |
| 6203 | 17 × 40 × 12 mm | 17 × 40 × 7 mm |
| 6204 | 20 × 47 × 14 mm | 20 × 47 × 7 mm |
| 6205 | 25 × 52 × 15 mm | 25 × 52 × 7 mm |
| 6206 | 30 × 62 × 16 mm | 30 × 62 × 7 mm |
| 6207 | 35 × 72 × 17 mm | 35 × 72 × 10 mm |
| 6208 | 40 × 80 × 18 mm | 40 × 80 × 10 mm |
| 6210 | 50 × 90 × 20 mm | 50 × 90 × 10 mm |
| 6305 | 25 × 62 × 17 mm | 25 × 62 × 7 mm |
| 6306 | 30 × 72 × 19 mm | 30 × 72 × 10 mm |
| 6308 | 40 × 90 × 23 mm | 40 × 90 × 10 mm |
| 6310 | 50 × 110 × 27 mm | 50 × 110 × 10 mm |
| 22216 | 80 × 140 × 33 mm | 80 × 140 × 12 mm |
| 30205 | 25 × 52 × 16.25 mm | 25 × 52 × 7 mm |
All sizes and the bearings they fit are in the seal size table. The bearing finder also shows the matching seal for every bearing.
Frequently asked questions
Which seal fits a 6205 bearing?
25 × 52 × 7 mm; if the housing has more room, a wider seal with the same diameters can be used.
Should I choose NBR or FKM?
Up to 100 °C NBR is sufficient and cheaper; choose FKM for hotter or chemical environments.
Are an oil seal, a shaft seal and a “Simmerring” the same thing?
Yes – they are common names for the radial shaft seal (Simmerring is a registered brand name).
